Skip to content Skip to sidebar Skip to footer

How To Replace The Blower Motor Resistor On A 2009 Toyota Tacoma

AUTEX Manual HVAC Blower Motor Resistor Compatible with Toyota
AUTEX Manual HVAC Blower Motor Resistor Compatible with Toyota from www.partstime.com

Are you the proud owner of a 2009 Toyota Tacoma? If so, you know that this is one of the most reliable pickup trucks on the road. But even the most reliable vehicles need servicing from time to time and one of the most common issues that Tacoma owners face is a faulty blower motor resistor. This can cause the fan blower to only work on high or not work at all. But don't worry, replacing the blower motor resistor is a fairly simple task and can be done in an hour or less by most people. In this article, we'll show you how to do it.

What is the Blower Motor Resistor?

Before we get into the steps on how to replace the blower motor resistor, let's take a moment to discuss what it is and why it's important. The blower motor resistor is a part of the vehicle's climate control system. It is responsible for controlling the fan speed of the heater and air conditioner. Without it, the fan blower would only work on high and you wouldn't be able to adjust the fan speed.

Tools and Parts Needed

Now that we know what the blower motor resistor is and why it's important, let's take a look at the tools and parts you'll need to complete the job. You'll need a #2 Phillips head screwdriver, a 7mm socket wrench, a flat head screwdriver, and a new blower motor resistor for your 2009 Toyota Tacoma. You can find the replacement parts online or at your local auto parts store.

Step 1: Disconnect the Battery

The first step in replacing the blower motor resistor on your 2009 Toyota Tacoma is to disconnect the battery. This can be done by loosening the negative cable with a #2 Phillips head screwdriver and then pulling it off. Make sure the battery is completely disconnected before you move on to the next step.

Step 2: Remove the Glove Box

The next step is to remove the glove box. This can be done by removing the two screws at the bottom of the glove box with a #2 Phillips head screwdriver. Once the screws are removed, you can open the glove box and then pull it out. Be careful not to break the plastic tabs that hold the glove box in place.

Step 3: Remove the Blower Motor Resistor

Once the glove box is removed, you'll see the blower motor resistor. It should be located just above the blower motor. You'll need to use a 7mm socket wrench to remove the two screws that hold the blower motor resistor in place. Once the screws are removed, you can pull out the blower motor resistor.

Step 4: Install the New Blower Motor Resistor

Now that the old blower motor resistor is removed, you can install the new one. Take the new blower motor resistor and place it in the same position as the old one. Make sure all the pins are aligned properly. Once it's in place, use a 7mm socket wrench to tighten the two screws.

Step 5: Reattach the Glove Box

The next step is to reattach the glove box. This can be done by inserting the glove box back into the dash and then using a flat head screwdriver to tighten the two screws. Once the screws are tightened, the glove box should be securely in place.

Step 6: Reconnect the Battery

The last step is to reconnect the battery. This can be done by placing the negative cable back onto the battery and then using a #2 Phillips head screwdriver to tighten it. Make sure the cable is securely in place before you move on.

Conclusion

Replacing the blower motor resistor on your 2009 Toyota Tacoma is a fairly simple task that can be done in an hour or less. All you'll need is a few tools and a new blower motor resistor and you'll be back on the road in no time. If you have any questions or need help with the process, don't hesitate to ask a qualified mechanic.